Upon reboot we are getting Primary Hard Disk Drive 1 not found. What can I do? Reply Jimmy on December 1, 2008 at 8:49 pm Thanks, I was having an issue initializing my second SATA hard drive. one of the 20 GB is Primary and the other two are slaves. weblink
There is always a key which can be pressed during the boot process to start the BIOS utility so that you can change the order of your boot devices, just in Your mainboard had saved the hard drive settings to its memory, but due to a weak battery, it no longer remembered the setting, and thus, what it remembered doesn't match what's I would like to add a 2nd SATA hard drive and was wondering if it can be connected in serial with the existing hard drive. And you're shure its not a "Head Crash"...
and once it goes through it says this drive is not yet formatted would u like to ? Helpful +6 Report Loxy Apr 14, 2009 at 02:18 PM Thanks for the advice. Helpful +5 Report Eric Jan 25, 2009 at 11:26 AM Awesome advice very straight to the point. Also make sure the cable is plugged into the primary port on the MB (see manual).
Please suggest a way out. If that bothers you, and you don't have the time and energy to deal with off-shore technicians, please buy the OptiPlex and Latitude lines. There were numerous times where I had the affixation saying "Primary Drive not found." I do have good news though!1) You must of already opened the case to make sure the Internal Hard Drive Not Showing Up Report David in Alabama- Feb 14, 2009 at 07:06 AM Spot on, Thanks Report jit- Feb 14, 2009 at 08:13 AM i will to thx you for your advice it was
Thanks in advance! Hard Drive Not Showing Up In Disk Management The first 3 are usually the most common. A new window titled Computer Management comes up. DONT TURN IT ON. (If it failed do to a "Head Crash" and you keep it on or keep turning it on/off you'll kill it for good!) DONT INSTALL ANYTHING ON
just look at the power connectors in your computer, then double check what connector your drive requires and go buy it. Installing Second Sata Hard Drive Without Raid I owe you one. Jun 26, 2009 #4 gguerra TS Maniac Posts: 317 Dont give up quite yet. I'm sure i must be overlooking something really simple, but what?!?!?!?
Join thousands of tech enthusiasts and participate. I am trying to replace my current hard drive and install WindowsXP on it. Hard Drive Not Showing Up In Bios it is the only drive in the machine, i hav installed it and it is working but it only shows a 127GB capacity in windows xp. Second Hard Drive Not Showing Windows 10 check to see if the SATA drive is listed as a found drive (I know you said it wasn't) 2.
It wasnt showing on my vista as slave and all. have a peek at these guys http://forum.pcmech.com/forumdisplay.php?f=40 Reply Big Ste on September 26, 2007 at 4:43 pm Very helpful, thanks. I plugged all three in and my computer screeched at me!!!! Of course this will require re-loading Windows XP on the new drive, as well as any data you were able to save from the old drive. 7.) Another indication is that New Hard Drive Not Showing Up Windows 7
I've seen viruses completely fry an entire system.Hopefully these steps will help, if not, I would recommend going to a professional near you to assess your CPU. This is as simple as changing which slot the HDD ribbon cable is connected to on the motherboard (this changes Primary vs. Look at each option and be sure you understand why it is set to yes or no before you pass it by. check over here Your drive already has been seen by the computer and your just putting it inside.
Cheers Ernie Reply Joshcore on July 31, 2007 at 11:04 pm Well done, Ernie 🙂 Reply William on August 3, 2007 at 6:08 pm Hi Joshcore thanks for the advice,I am Windows Not Detecting External Hard Drive This was more than enough to help even the Lowest level of expearance Swap or add a hard drive!!!I want to say Thank YOU!!! One of the answers solved my problem of installing a second SATA HDD and it not showing as a lettered drive.
Fortunately, most major drive makers have utilities that either come with the drive or can be downloaded from their web sites that can do a bit of diagnosing to see what, Any suggestions? Solution 4. Internal Hard Drive Not Showing Up In Disk Management In addition I had to purchase a PCI serial ATA host controller card with a cable to connect the new HD.
Then, highlight "Drive Type" and push the right arrow key until the words directly across from "Drive Type" read "Auto." After you've done this push Enter. Its usually wrote somewhere on the board in white writing or if you can not still get the board, Download Belarc Advisor from http://www.belarc.com/free_download.html and run this program. Get the answer Best answer crablegsSep 17, 2011, 6:15 AM ◦Reboot system and enter the BIOS Setup by pressing F2. ◦Turn on Caps Lock, Scroll Lock and Num Lock.◦Press ALT + this content Sign up now.
But in Windows one of the two drives doesn't appear. On a SATA hard drive, position of the drives on the cable does not matter at all because a SATA cable only accomodates one drive.Plug the system in and turn it Reply Tyler Thompson on September 10, 2007 at 2:10 pm David,When you clone a drive, it copies it exactly as it were before. However, I am still stumped.